INCRA

Product Description

Instead Of Squinting At That Blur Of Lines Along The Edge Of Your Old Steel Rule, The Incra 12-Inch Marking Rule Set, Lets You Mark Precisely Where You Want With Zero Uncertainty And No Eye Strain. Incra Has Re-Invented The Steel Rule By Putting Micro-Fine Holes At Every Scale Position (Every 1/16-Inch And 1/32-Inch) To Instantly Locate A Sharp Pencil Or Scribe Exactly On Target. Using A T-Square This Guide Draws Perfectly Placed Horizontal Lines With Dead-On Accuracy, With Guide Slots That Wrap Around Any Edges.

Amazon.com

Instead of squinting at that blur of lines along the edge of your old steel rule, the Incra 12-Inch Marking Rule Set, lets you mark precisely where you want with zero uncertainty and no eye strain. Incra has re-invented the steel rule by putting micro-fine holes at every scale position (every 1/16-inch and 1/32-inch) to instantly locate a sharp pencil or scribe exactly on target. Using a T-square this guide draws perfectly placed horizontal lines with dead-on accuracy, with guide slots that wrap around any edges.

See all Product description

INCRA Bend Rules make dual-surface layouts a snap using the corner slots shown above. The INCRA Bend Rule is precisely what you need for layout and measurement along the edge of a board or other workpiece. Weve put micro-fine marking holes at every scale line to instantly locate your sharp pencil point or scribe exactly on target with zero undertainty and no eye strain! The 90 shape holds it snugly in place while the two scale surfaces let you mark and measure on the top, edge and corners simultaneously! There are even two vertical end scales for drawing precision parallel lines relative to the edge of your work. All three lengths of bend rules are also available in INCRA Rule Sets. The Bend Rule draws perfect horizontal lines using the end marking holes while sliding the rule along the edge of your work!

This is our Metric T-Rule shown here is the 150mm version. It is also available in a 300mm length. These rules offer INCRAs patented marking holes at every full, 1/4, 1/2 and 3/4mm from 0 to 150mm. They also offer 0 to 50mm height marking slots on the end in millimeters.

The New INCRA Bend Rule is precisely what you need for layout and measurement along the edge of a board or other workpiece. We’ve put micro-fine marking holes every 1/16″ and 1/32″ to instantly locate your sharp pencil point or scribe EXACTLY on target with zero uncertainty, zero parallax and zero eye strain. The 90 deg. shape holds it snugly in place while the two scale surfaces let you mark and measure on the top, edge and corners simultaneously. There are even two vertical end scales with marking holes for drawing precision parallel lines relative to the edge of your work. Available in 6″, 12″ and 18″ lengths. Engraved stainless steel.

For precision measurement of metric items, INCRA’s precision measuring tools will help you accomplish your project with accuracy. It is best used with a mechanical pencil for wood or scriber for metal. The 300 mm T-rule has INCRA’s patented marking holes at every full, 1/4, 1/2 and 3/4 mm from 0 to 300 mm. It also has 0 to 50 mm height marking slots on the end in millimeters. Made in U.S.A.

Product description

Find the exact center of any workpiece up to 12″ wide. Has a built-in protractor, too.

From the Manufacturer

Find the exact center of any workpiece up to 12″ wide. In addition to top and bottom micro-fine marking holes at every 1/32″ it also has a built-in protractor with guide slots at every 45°, 30°, 22.5°, and 5° interval.

From the Manufacturer

INCRA Precision Marking Rules. At first glance you might think you are looking at an ordinary ruler. But look closer and you will see micro-fine marking holes and slots every 1/16″, 1/32″ and 1/64″ to instantly locate a sharp pencil point or scribe EXACTLY where you want it. No more squinting as you try to line up your pencil on that blur of lines along the edge of your old steel rule. Even when the lighting is less than perfect, you can effortlessly place your mark precisely on target with zero uncertainty, zero parallax and zero eye strain. Who would have thought there was so much room for improvement in the common ruler. There WAS and INCRA RULES is it! Available in 6″, 12″ and 18″ lengths. Engraved stainless steel.

Limited Quantity Special Deals INCRA scores again with its precision steel rule. Select the proper slot or hole, insert a .5mm mechanical pencil, and mark the measurement with dead-on accuracy. Made in U.S.A.

Product Description

Precise, Versatile, And Easy-To-Use Are The Words Which Best Describe The Incra 12-Inch Precision Marking T-Rule. Think Of It As A Combination Square For Marking Or Measuring That’s Simultaneously Set To Every Scale Position With Perfect, Instant Accuracy. There Are Micro-Fine Marking Holes And Slots At Every 1/16-, 1/32-, And 1/64-Inch Scale Position To Instantly Locate Your Sharp Pencil Or Scribe Exactly On Target With Zero Uncertainty. The Incra T-Rule Makes It Very Easy To Draw Exact Lines In Either Direction, And With Zero Uncertainty And No Eye Strain. Other Features Include 0- To 3-Inch Height Markings On The End In 32Nds, And The Option Of Marking Holes Every 1/100-Inch. The Product Also Comes With A Limited 1-Year Warranty.

Amazon.com

Precise, versatile, and easy-to-use are the words which best describe the Incra 12-Inch Precision Marking T-Rule. Think of it as a combination square for marking or measuring that’s simultaneously set to every scale position with perfect, instant accuracy. There are micro-fine marking holes and slots at every 1/16-, 1/32-, and 1/64-inch scale position to instantly locate your sharp pencil or scribe exactly on target with zero uncertainty. The Incra T-Rule makes it very easy to draw exact lines in either direction, and with zero uncertainty and no eye strain. Other features include 0- to 3-inch height markings on the end in 32nds, and the option of marking holes every 1/100-inch. The product also comes with a limited 1-year warranty.

See all Product description